How to Set up a Tub Yourself
How to Set up a Tub Yourself
Blog Article
We've unearthed this post relating to A Step-by-Step Guide to Installing a Bathtub listed below on the internet and felt it made perfect sense to write about it with you on this site.
Installing a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old bathtub with a new one is also a moderately challenging project. If the old tub is readily obtainable, the job can move immediately; if you need to open up a wall to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and also set in the brand-new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This post will certainly help you install a new bathtub in your restroom if you have already purchased a new tub and don't require to transform the setup of your previous water pipelines.
Your devices as well as material checklist ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the limited access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will come from the pipelines. Once the supply pipelines have been removed, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, place the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leaks and also tighten them if essential. Load the tub and also examine the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has been made use of at the very least once as this will resolve it right into its final setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area between the tap as well as the sink. Protect the tap in position with the supplier supplied backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind ought to be connected to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in problems with dampness and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not think about this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof adhesive as well as cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you liked our article on A Step-by-Step Guide to Installing a Bathtub. Thanks for taking time to read our blog. Enjoyed reading our piece? Please share it. Help others check it out. We thank you for reading our article about Installing A Bathtub.
Schedule Appointment
Report this page